# -*- text -*-
######################################################################
#
#	This is a sample configuration for robust proxy accounting.
#	accounting packets are proxied, OR logged locally if all
#	home servers are down.  When the home servers come back up,
#	the accounting packets are forwarded.
#
#	This method enables the server to proxy all packets to the
#	home servers when they're up, AND to avoid writing to the
#	detail file in most situations.
#
#	In most situations, proxying of accounting messages is done
#	in a "pass-through" fashion.  If the home server does not
#	respond, then the proxy server does not respond to the NAS.
#	That means that the NAS must retransmit packets, sometimes
#	forever.  This example shows how the proxy server can still
#	respond to the NAS, even if all home servers are down.
#
#	This configuration could be done MUCH more simply if ALL
#	packets were written to the detail file.  But that would
#	involve a lot more disk writes, which may not be a good idea.
#
#	This file is NOT meant to be used as-is.  It needs to be
#	edited to match your local configuration.
#
#	Please see the sites-available/default file, in the
#	"Post-Proxy-Type Fail-Accounting" section.  That should be
#	configured to write packets to the "detail.example.com"
#	file when proxying fails.  The "listen" section below will
#	then read packets from that file, and proxy them.
#
#	See also mods-available/detail.example.com, which is the
#	module that writes the "detail.example.com" file.
#
#
#	$Id: 85f2f9dcc06ed2cc2c14d371c7cfc5a086b4c6cf $
#
######################################################################

#  (1) Define two home servers.
home_server home1.example.com {
	type = acct
	ipaddr = 192.0.2.10
	port = 1813
	secret = testing123

	#  Mark this home server alive ONLY when it starts being responsive
	status_check = request
	username = "test_user_status_check"

	#  Set the response timeout aggressively low.
	#  You MAY have to increase this, depending on tests with
	#  your local installation.
	response_window = 6
}

home_server home2.example.com {
	type = acct
	ipaddr = 192.0.2.20
	port = 1813
	secret = testing123

	#  Mark this home server alive ONLY when it starts being responsive
	status_check = request
	username = "test_user_status_check"

	#  Set the response timeout aggressively low.
	#  You MAY have to increase this, depending on tests with
	#  your local installation.
	response_window = 6
}

#  (2) Put all of the servers into a pool.
home_server_pool acct_pool.example.com {
	type = load-balance	# other types are OK, too.

	home_server = home1.example.com
	home_server = home2.example.com
	# add more home_server's here.

	# for pre/post-proxy policies
	virtual_server = home.example.com
}

#  (3) Define a realm for these home servers.
#  It should NOT be used as part of normal proxying decisions!
realm acct_realm.example.com {
	acct_pool = acct_pool.example.com
}

#  (4) Define a detail file writer.
#   See raddb/modules/detail.example.com

#  (5) Define a virtual server to handle pre/post-proxy re-writing
server home.example.com {
	pre-proxy {
		#  Insert pre-proxy rules here
	}

	post-proxy {
		#  Insert post-proxy rules here

		#  This will be called when the CURRENT packet failed
		#  to be proxied.  This may happen when one home server
		#  suddenly goes down, even though another home server
		#  may be alive.
		#
		#  i.e. the current request has run out of time, so it
		#  cannot fail over to another (possibly) alive server.
		#
		#  We want to respond to the NAS, so that it can stop
		#  re-sending the packet.  We write the packet to the
		#  "detail" file, where it will be read, and sent to
		#  another home server.
		#
		Post-Proxy-Type Fail-Accounting {
			detail.example.com
		}

		#
		#  This section is run when there are problems
		#  proxying Access-Request packets
		#
		Post-Proxy-Type Fail-Authentication {
			# add policies here
		}

	}


	#  Read accounting packets from the detail file(s) for
	#  the home server.
	#
	#  Note that you can have only ONE "listen" section reading
	#  detail files from a particular directory.  That is why the
	#  destination host name is used as part of the directory name
	#  below.  Having two "listen" sections reading detail files
	#  from the same directory WILL cause problems.  The packets
	#  may be read by one, the other, or both "listen" sections.
	listen {
		type = detail
		filename = "${radacctdir}/detail.example.com/detail-*:*"
		load_factor = 10
	}

	#  All packets read from the detail file are proxied back to
	#  the home servers.
	#
	#  The normal pre/post-proxy rules are applied to them, too.
	#
	#  If the home servers are STILL down, then the server stops
	#  reading the detail file, and queues the packets for a later
	#  retransmission.  The Post-Proxy-Type "Fail" handler is NOT
	#  called.
	#
	#  When the home servers come back up, the packets are forwarded,
	#  and the detail file processed as normal.
	accounting {
		# You may want accounting policies here...

		update control {
			&Proxy-To-Realm := 'acct_realm.example.com'
		}
	}

}